myHanse.com - Hanse Yacht Owners Website myHanse.com - Hanse Yacht Owners Website myHanse.com - Hanse Yacht Owners Website myHanse.com - Hanse Yacht Owners Website

Welcome to myHanse.com the forum for Hanse Yachts owners throughout the world.

Forum Home Forum Home > Hints and Tips > 430
  New Posts New Posts RSS Feed - Cockpit traveler
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Cockpit traveler

 Post Reply Post Reply Page  12>
Author
Message Reverse Sort Order
nibheis View Drop Down
Lieutenant Commander
Lieutenant Commander
Avatar

Joined: 16 August 2012
Location: France
Status: Offline
Points: 57
Post Options Post Options   Thanks (0) Thanks(0)   Quote nibheis Quote  Post ReplyReply Direct Link To This Post Topic: Cockpit traveler
    Posted: 08 July 2017 at 07:39
Yes, sure. Here are 2 more photos of the table:





We are 5 on board, and the table size is fine. 6 would fit OK, we've done 8 if I remember well. It's quite easy to set up, our young kids do it fine.

Best regards,
nibheis

https://agile4life.blog

Edited by nibheis - 08 July 2017 at 07:41
Back to Top
iemand View Drop Down
Vice Admiral
Vice Admiral
Avatar

Joined: 13 February 2004
Location: Germany
Status: Offline
Points: 800
Post Options Post Options   Thanks (0) Thanks(0)   Quote iemand Quote  Post ReplyReply Direct Link To This Post Posted: 06 July 2017 at 12:43
would you mind to post more pics?
Hanse 312 MJ 2004 - Hanse 370e MJ 2007
Back to Top
nibheis View Drop Down
Lieutenant Commander
Lieutenant Commander
Avatar

Joined: 16 August 2012
Location: France
Status: Offline
Points: 57
Post Options Post Options   Thanks (0) Thanks(0)   Quote nibheis Quote  Post ReplyReply Direct Link To This Post Posted: 06 July 2017 at 10:23
Hi!

I did not do anything to the cockpit floor... I purchased the boat like this. It had been ordered like this at the factory, I suppose.

There is no fixed cockpit table, the 6:1 is anchored on a 10 mm chainplate on the cockpit floor, with a counter plate below the floor.

Then, there is a folding teak table that is visible on the photos. It folds flat on the cockpit floor; this is why the cockpit floor looks different.

Best regards,
nibheis

Back to Top
iemand View Drop Down
Vice Admiral
Vice Admiral
Avatar

Joined: 13 February 2004
Location: Germany
Status: Offline
Points: 800
Post Options Post Options   Thanks (0) Thanks(0)   Quote iemand Quote  Post ReplyReply Direct Link To This Post Posted: 02 July 2017 at 15:25
What have you done with your cockpit floor?

Hanse 312 MJ 2004 - Hanse 370e MJ 2007
Back to Top
Frankplast View Drop Down
Sub Lieutenant
Sub Lieutenant
Avatar

Joined: 10 June 2017
Location: Milano
Status: Offline
Points: 2
Post Options Post Options   Thanks (0) Thanks(0)   Quote Frankplast Quote  Post ReplyReply Direct Link To This Post Posted: 02 July 2017 at 10:42
It looks very effective! Thank you very much to both of you! Smile



Edited by Frankplast - 02 July 2017 at 10:50
Back to Top
nibheis View Drop Down
Lieutenant Commander
Lieutenant Commander
Avatar

Joined: 16 August 2012
Location: France
Status: Offline
Points: 57
Post Options Post Options   Thanks (0) Thanks(0)   Quote nibheis Quote  Post ReplyReply Direct Link To This Post Posted: 14 June 2017 at 14:07
Hi Frankplast,

Here are photos (almost live!) from my cockpit traveller. I would call it 'hybrid' because it is half german sheeting and half with a 6:1 (after the 3:1 of the german sheeting on the cockpit side).

Photos are better than words:







As Rubato mentionned, the rail is a 'thick' one because of the bridge it makes between the seats (it has not moved a bit over the last 9 years).
Also, the 6:1 is anchored on the cockpit floor. The rail only supports 2/3rd of the load.

In light winds, we like to anchor the german sheet directly on the cockpit floor to avoid having the 6:1 flying across the cockpit when the boom swings - and we don't need the 6:1 in those conditions.

The german sheeting is very effective, and the 6:1 (in fact a 18:1) works well, it is nice to control the rail and the sheet from the helm.

Best regards,
nibheis
Back to Top
Rubato View Drop Down
Admiral
Admiral
Avatar

Joined: 12 July 2006
Location: Canada
Status: Offline
Points: 1613
Post Options Post Options   Thanks (1) Thanks(1)   Quote Rubato Quote  Post ReplyReply Direct Link To This Post Posted: 13 June 2017 at 18:32
You may have to support the beam in the middle with a rod to the cockpit floor. Check the specifications of the beam you intend to use, each size has a maximum span spec.

Personally, I'd recommend a German or Admiral's Cup sheet system using dedicated winches. http://www.harken.com/content.aspx?id=3901  

I initially tried a coarse/fine system on my 400 and it did not work well and I suggest it will be even worse on the 430. It was 6:1 and 24:1. You could not bring the 6:1 in hard enough by hand such that the travel of the 24:1 was enough to set the sail correctly. In the end, the German sheeting works so much better...
Steve

Hanse 400e, #168
Back to Top
nibheis View Drop Down
Lieutenant Commander
Lieutenant Commander
Avatar

Joined: 16 August 2012
Location: France
Status: Offline
Points: 57
Post Options Post Options   Thanks (0) Thanks(0)   Quote nibheis Quote  Post ReplyReply Direct Link To This Post Posted: 12 June 2017 at 07:38
I just checked under the seats, there is an added (and massive) GRP backing plate right under the rail (and 4 x 10 or 12 mm bolts) on each side.

I said 'added' because this backing plate does not appear in the 2 PDF I sent you.

Just check under your seat for this backing plate. If it's not here, you can add one.

Best regards,
nibheis
Back to Top
nibheis View Drop Down
Lieutenant Commander
Lieutenant Commander
Avatar

Joined: 16 August 2012
Location: France
Status: Offline
Points: 57
Post Options Post Options   Thanks (0) Thanks(0)   Quote nibheis Quote  Post ReplyReply Direct Link To This Post Posted: 12 June 2017 at 07:18
Here are the 2 documents I have about steel and/or aluminum reinforcements on the deck.


h430_Reinforcements.pdf

h430_Reinforcements2.pdf

Edited by nibheis - 12 June 2017 at 07:19
Back to Top
Frankplast View Drop Down
Sub Lieutenant
Sub Lieutenant
Avatar

Joined: 10 June 2017
Location: Milano
Status: Offline
Points: 2
Post Options Post Options   Thanks (0) Thanks(0)   Quote Frankplast Quote  Post ReplyReply Direct Link To This Post Posted: 10 June 2017 at 13:05
Hi, I would like to install a cockpit traveler in my Hanse 430e in which there is already the table provided by the factory. 
I sent an email to hanse to ask if the reinforcements on the lateral seats (where they mount the traveller when it is set up in the factory) are provided in every boat, including the ones where the table is set up. They haven't answered yet so I am asking if anybody knows anything about this issue. 
I have checked the seats from the inside but it is not clear weather or not there are metal reinforcements embedded in the structure. 
Thank you


Edited by Frankplast - 10 June 2017 at 13:09
Back to Top
 Post Reply Post Reply Page  12>
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.04
Copyright ©2001-2015 Web Wiz Ltd.

This page was generated in 0.078 seconds.

Links : www.hanseyachts.co.uk www.hanseyachts.com www.fjordboats.co.uk www.dehler.co.uk www.varianta.co.uk