myHanse.com - Hanse Yacht Owners Website myHanse.com - Hanse Yacht Owners Website myHanse.com - Hanse Yacht Owners Website myHanse.com - Hanse Yacht Owners Website

Welcome to myHanse.com the forum for Hanse Yachts owners throughout the world.

Forum Home Forum Home > Hints & Tips > 341 / 342
  New Posts New Posts RSS Feed - Check points for survey
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Check points for survey

 Post Reply Post Reply
Author
Message
PALM View Drop Down
Lieutenant
Lieutenant
Avatar

Joined: 29 October 2009
Status: Offline
Points: 41
Post Options Post Options   Thanks (0) Thanks(0)   Quote PALM Quote  Post ReplyReply Direct Link To This Post Topic: Check points for survey
    Posted: 01 November 2009 at 16:37
I am looking for a 342 and had a short mail conversation with Johan Hackman on issues to look for at a survey.
 
I found this forum after I looked on the boat of my interest and is now trying to collect known issues before the second survey.

Issues from this forum:
* Cracked/leaking rudder.
* Right size rudder. The size of the rudder shall be approx 165cm for deep keel. Approx 135cm for shallow keel.
* Anchor box drain hole drilled at wrong place (through balsa sandwich). The hole shall be located close to the bow.
* Electric bildge pump not working.
 
Issue from my survey:
* Bolts through deck holding the side shrouds attachments leaking. Bolts slightly corroded on inside.

Please add other known issues (also the small ones)!
 
Kind regards
Petter Almhagen
Sweden
 
Picture (copy from Johan Hackman) specifying the drain hole position.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 


Edited by PALM - 06 November 2009 at 20:56
Back to Top
iliohale View Drop Down
Captain
Captain
Avatar

Joined: 15 June 2009
Location: United States
Status: Offline
Points: 185
Post Options Post Options   Thanks (0) Thanks(0)   Quote iliohale Quote  Post ReplyReply Direct Link To This Post Posted: 02 November 2009 at 03:11
If the boat has electrical bonding, be sure that the thru hulls are all solid and that you have a proper anode tied to the system.
iliohale, Hanse 341
San Francisco, CA USA
Back to Top
Johan Hackman View Drop Down
Admiral of the Fleet
Admiral of the Fleet
Avatar

Joined: 24 August 2005
Location: Sweden
Status: Offline
Points: 4262
Post Options Post Options   Thanks (0) Thanks(0)   Quote Johan Hackman Quote  Post ReplyReply Direct Link To This Post Posted: 02 November 2009 at 20:56
It's good to see that yet another buyer finds this forum useful.

Obviously, buying second hand is a lot different from buying brand new (which is my only experience) but I think the major disasters have been covered in this thread already. The single most important issue in my opinion is the anchor locker drain because if there has been water ingress in the balsa core repairs can be very costly. A damaged rudder can always be replaced albeit expensively. Jefa have announced that they have a ready rudder to offer. If the bilge pump is not fit for the purpose you just have to replace it with one that is to a relatively small cost. The only thing you have to do is to test it to see if it works or not. Only two people at this forum have reported that they have tested theirs though, so you might want to leave that until you boat actually starts to sink.

Had your prospective boat been a bit younger you would have had to face the dreaded bath platform problem but your boat has inherited the 341 stern so you can luckily forget about that.

I would check the aft part of the keel just to make sure that it is not damaged from any groundings. Even a grounding at fairly low speed will make the keel crack because the aftermost keel bolt is positioned way to close to the edge of the keel.

Johan



Edited by Johan Hackman - 02 November 2009 at 21:16
Back to Top
kirkelund View Drop Down
Vice Admiral
Vice Admiral


Joined: 29 June 2009
Status: Offline
Points: 949
Post Options Post Options   Thanks (0) Thanks(0)   Quote kirkelund Quote  Post ReplyReply Direct Link To This Post Posted: 05 November 2009 at 23:02
Hi Johan

I agree with the check list including the rudder issue, which I think is a strange Hanse mistakeConfused. I have noticed your opinion concerning the anchor locker drain. As you point out, drilling through the sandwich laminate should be avoided unless, of course, precations have been made to prevent water ingress. I am not sure exactly where, in your opinion, the hole should be placed. (I would think it shold be placed at the low point of the anchor locker floor in any case). I have added a photo of my Hanse 342, on shore, where you can se the placement of the anchor locker drain from outside. What do you think?

Ole Kirkelund
Ishøj, Denmark




Edited by kirkelund - 05 November 2009 at 23:04
Back to Top
Johan Hackman View Drop Down
Admiral of the Fleet
Admiral of the Fleet
Avatar

Joined: 24 August 2005
Location: Sweden
Status: Offline
Points: 4262
Post Options Post Options   Thanks (0) Thanks(0)   Quote Johan Hackman Quote  Post ReplyReply Direct Link To This Post Posted: 05 November 2009 at 23:47
Originally posted by kirkelund kirkelund wrote:

As you point out, drilling through the sandwich laminate should be avoided unless, of course, precations have been made to prevent water ingress.


Ole, you are right about "precautions". For example, if you look at the through-hulls in the bathroom you will see that Hanse have been wise enough to make it single laminate around that area. If you take a look you will see that the hull is thinner there.

The below picture shows the "precautions" around the anchor locker drain on my boat, which was a metal pipe and some sealant. Needless to say, this was far from satisfactory and sure enough there had been water ingress in the balsa core already after two years.



The anchor locker is probably the place that dries last after a sail or a rain so I would say the drain is one of the most vulnerable places when you drill a hole through the sandwich. I know for a fact that Hanse is well aware that they have made the same mistake on a lot of boats and still I haven't seen any sign that they are willing to make it straight. I think a general recall is in place here. I have got my boat fixed though, but it involved hiring an expensive lawyer.

Then, if you take a look at the first post at the top of this thread you will see where in the anchor locker the hole should have been drilled to make sure that it is drilled through solid laminate. Petter has been kind enough to show where, using one of my pictures taken after the repair.

I personally wouldn't bother too much if the hole is not at the lowest point of the locker. Since the locker will be wet almost all the time a little standing water will not be such a great problem. On a sunny day the water will find its way out by the movements of the boat anyway.

The below photo shows how the hull around the drain was repaired on my boat. The sole was removed, as well as the inner laminate. The damp balsa was then replaced with GRP and the sole laminated back in place and a new hole was drilled in the original position.

Johan

Back to Top
kirkelund View Drop Down
Vice Admiral
Vice Admiral


Joined: 29 June 2009
Status: Offline
Points: 949
Post Options Post Options   Thanks (0) Thanks(0)   Quote kirkelund Quote  Post ReplyReply Direct Link To This Post Posted: 06 November 2009 at 19:57
Super - thanks for the pictures, Johan (great as alwaysSmile) and to Petter for posting the picture of you new drainage.

I will keep an eye on the my anchor locker, which seems to have the drain in the wrong position.

Ole.
Back to Top
Johan Hackman View Drop Down
Admiral of the Fleet
Admiral of the Fleet
Avatar

Joined: 24 August 2005
Location: Sweden
Status: Offline
Points: 4262
Post Options Post Options   Thanks (0) Thanks(0)   Quote Johan Hackman Quote  Post ReplyReply Direct Link To This Post Posted: 17 November 2009 at 22:54
I just came to think about another thing that has previously been discussed.

There should be a delrin washer between the upper bearing housing and the stopping ring on the rudder stock. Otherwise it will be aluminium to aluminium which might create problems with friction and ugly noices. The collar on the stock is pressing upwards since the rudder blade has quite some buyancy which can be seen here.

If the washer is missing one should make sure to get one.

Johan

Back to Top
Matros View Drop Down
Captain
Captain
Avatar

Joined: 27 July 2009
Status: Offline
Points: 331
Post Options Post Options   Thanks (0) Thanks(0)   Quote Matros Quote  Post ReplyReply Direct Link To This Post Posted: 18 November 2009 at 08:51

Johan,

This problem only applies to boats with tiller steering, right? I can’t recognize this construction on my 342.

S/Y Rosetta, Hanse 342 # 245
Definition: boat, a hole in the surface of water, into which money is thrown.
Back to Top
Johan Hackman View Drop Down
Admiral of the Fleet
Admiral of the Fleet
Avatar

Joined: 24 August 2005
Location: Sweden
Status: Offline
Points: 4262
Post Options Post Options   Thanks (0) Thanks(0)   Quote Johan Hackman Quote  Post ReplyReply Direct Link To This Post Posted: 18 November 2009 at 09:02
There should be a delrin washer between the collar and the bearing housing even on a wheel-steered boat. The only difference should be that the steering is attached directly to the stock. That might be the reason you don't recognize it.

Johan
Back to Top
 Post Reply Post Reply

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.06
Copyright ©2001-2023 Web Wiz Ltd.

This page was generated in 0.297 seconds.

Links : www.hanseyachts.co.uk www.hanseyachts.com www.fjordboats.co.uk www.dehler.co.uk www.varianta.co.uk