Welcome to myHanse.com the forum for Hanse Yachts owners throughout the world. | |
Main hatch |
Post Reply | Page 12> |
Author | ||
Scottie
Sub Lieutenant Joined: 26 January 2011 Location: United Kingdom Status: Offline Points: 16 |
Post Options
Thanks(0)
Posted: 16 April 2018 at 10:57 |
|
We have a problem with the retaining stop We have stored the vertical panels on top of the sliding panel and located them with wooden beading not sur if this is the normal method It would appear that the end portion of the pane has sheared along the line of fixing screws and dropped off Any suggestions how to access the end section I have not looked at it since the problem occurred so it might be self evident so will check today Has anyone else had similar problems? Thank you 370E |
||
Scotchmist
Captain Joined: 15 June 2008 Location: United Kingdom Status: Offline Points: 180 |
Post Options
Thanks(0)
|
|
Hi Scottie
You need to unscrew the hatch garage. When you do, you'll probably find that there were 2 hardwood battens screwed together through the perspex hatch (one below and 1 above). The screws have probably bent and possible damaged the perspex. Suggest replacing one of the battens (cant remember which), with aluminium angle section. Drill new oversize bolt holes in the hatch cover. Use rubber grommets as spacers in the perspex cover (they absorb the impact of the slamming against the stop), and bolt back together (don't use screws because the same problem will recur).
|
||
Andrew
Scotch Mischief Dehler 38 by Hanse |
||
Rubato
Admiral Joined: 12 July 2006 Location: Canada Status: Offline Points: 1791 |
Post Options
Thanks(0)
|
|
An alternative method is to add stops in the teak side rails so the hatch can't slide right out. I initially used 2 screws (one each side) and later changed it to an inserted steel rod with a rubber bushing on the outside.
|
||
Steve
Hanse 400e, #168 |
||
Scottie
Sub Lieutenant Joined: 26 January 2011 Location: United Kingdom Status: Offline Points: 16 |
Post Options
Thanks(0)
|
|
Thank you both
The garage is under both the spray hood and main sheet track so Will be an awkward job so stops will be going on for the time being |
||
Captain Cook
Admiral Joined: 23 May 2006 Location: Denmark Status: Offline Points: 1009 |
Post Options
Thanks(0)
|
|
I also had the problem, and like Rubato I put 2 screws with wide rubber bushings as stops. It has worked for several years now. I used a drill to remove the "star" in the screws, for burglary protection. If I want to change or remove the stops, I will have to cut the rubber and remove the screws the hard way.
My plan is to mount three small L-shaped aluminium profiles on top of the sliding hatch, so I have better control of the perspex board, which is normally placed there when cruising. Once in a while after heavy weather, the board seems to try to hide from me deep in the hatch-garage. |
||
Freya H400 #27 (2006), 40HP 3JH4E, 2-cabin, 3-blade Flexofold, Aries LiftUp Windvane, Exturn 300, Jefa DD1,Simrad NX40,Icom M603(VHF)+M802(SSB)
|
||
Rubato
Admiral Joined: 12 July 2006 Location: Canada Status: Offline Points: 1791 |
Post Options
Thanks(0)
|
|
I recall somewhere on this forum a number of years ago owner's showing a solution for this. They glued (epoxy?) some pieces of plexiglass (or acrylic) to the top of the hatch to hold the boards in place while sailing.
|
||
Steve
Hanse 400e, #168 |
||
samuel
Admiral of the Fleet Joined: 26 December 2004 Location: United Kingdom Status: Offline Points: 2683 |
Post Options
Thanks(0)
|
|
Mine is permanently attached by a cord so that if the boat was to be rolled in heavy weather or an inexperienced crew laid it incorrectly on the deck it would not get lost over the side. I can also pull it back with the cord when it goes under the hatch
|
||
Daydream Believer- Hanse 311- No GBR9917T- Bradwell Essex
|
||
Richard M
Captain Joined: 06 November 2006 Location: United Kingdom Status: Offline Points: 329 |
Post Options
Thanks(0)
|
|
I had a low tech solution on my 400e. I simply placed a strip of non-slip matting on the sliding hatch. This worked well.
|
||
Richard M
(S/Y BrightStar - H 455 #90; ex S/Y Providence - H 400e #290) |
||
MarcoC
Admiral Joined: 23 April 2009 Location: Sweden, Stockh. Status: Offline Points: 1617 |
Post Options
Thanks(0)
|
|
I think it was Johan Hackamn who did it if my memory serves me well.
|
||
"Älva"
Hanse 370#671 Stockholm, Sweden www.wesailhanse.se big wheel, deep draught iron keel, 3 cabins,Yanmar 3JH4E, Sparcraft rig. |
||
Captain Cook
Admiral Joined: 23 May 2006 Location: Denmark Status: Offline Points: 1009 |
Post Options
Thanks(0)
|
|
The search function in myhanse is a goldmine of information. I searched "glue hatch" (All forums/any date), and the subject "Seized hatch" from Sep 28 2010 by "Hansebonbon" appeared. The solution with a couple of small handles seems okay.
Edited by Captain Cook - 13 June 2018 at 23:50 |
||
Freya H400 #27 (2006), 40HP 3JH4E, 2-cabin, 3-blade Flexofold, Aries LiftUp Windvane, Exturn 300, Jefa DD1,Simrad NX40,Icom M603(VHF)+M802(SSB)
|
||
Post Reply | Page 12> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Links : www.hanseyachts.co.uk www.hanseyachts.com www.fjordboats.co.uk www.dehler.co.uk www.varianta.co.uk |