|
| |
| Welcome to myHanse.com the forum for Hanse Yachts owners throughout the world. | |
Pedestal angle and width |
Post Reply 
|
| Author | |
sv_palamut 
Lieutenant Commander 
Joined: 28 January 2024 Location: Netherlands Status: Offline Points: 61 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Pedestal angle and widthPosted: 22 May 2024 at 20:16 |
|
Hi,
I am not close to my boat right now, I was wondering if anyone knows the angle that the pedestal heels, and the width of the pedestal cross section. Many thanks in advance, Çağrı  Edited by sv_palamut - 22 May 2024 at 20:17 |
|
 |
|
|
sv_palamut
Lieutenant Commander
Joined: 28 January 2024 Location: Netherlands Status: Offline Points: 61 |
Post Options
Thanks(0)
Quote Reply
Posted: 26 May 2024 at 07:14 |
|
To conclude: this is 18 degrees.
The reason I was asking is, I am trying to order a hand grab. Cagri
|
|
|
|
|
Fendant
Admiral 
Joined: 03 November 2012 Location: Switzerland Status: Offline Points: 1671 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 May 2024 at 12:45 |
|
Hi Cagri,
where will you order the handgrabs? Any idea about the cost? BR Frank
|
|
|
Frank
|
|
|
|
|
sv_palamut
Lieutenant Commander
Joined: 28 January 2024 Location: Netherlands Status: Offline Points: 61 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 May 2024 at 12:51 |
|
Hi,
I had to get them custom made by a welder in NL. Picking them up today, let’s see how they look. I paid 500 euros for the pair. Cagri
|
|
|
|
|
sv_palamut
Lieutenant Commander
Joined: 28 January 2024 Location: Netherlands Status: Offline Points: 61 |
Post Options
Thanks(0)
Quote Reply
Posted: 01 June 2024 at 18:26 |
|
These are the photos of the end product, with my sloppy design/measurements. A bit higher than I wanted, but given that this was done based on remote design based on intuition (and a lot of inspiration from https://www.myhanse.com/grab-rails-for-steering-wheel_topic11061.html), I am satisfied with the result. I tapped threads to the alu pedestal, used 20mm m6 bolts with duralac, and plastic washers between the handle-grab lips and the pedestal. The installation took 2 hours. The welder is Paul, super friendly and accessible, I am happy working with him. Here is his instagram handle: https://www.instagram.com/paulie_smeltman/ .    |
|
|
|
|
Aussieangus
Commander 
Joined: 03 December 2019 Location: sydney Status: Offline Points: 93 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 June 2024 at 06:54 |
|
are you sure the bolts didnt go through into the area where the chain is?
|
|
|
Sydney Australia
GODS COUNTRY |
|
|
|
|
sv_palamut
Lieutenant Commander
Joined: 28 January 2024 Location: Netherlands Status: Offline Points: 61 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 June 2024 at 08:19 |
|
I am pretty sure, when I drilled, I was slow and careful. But after the hole was there, I poked it thoroughly, no contact.
If you follow the link above, the same mounting approach was used before as well.
|
|
|
|
|
Post Reply
|
|
| Tweet |
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
|
Links : www.hanseyachts.co.uk www.hanseyachts.com www.fjordboats.co.uk www.dehler.co.uk www.varianta.co.uk |
Topic Options